RLH Industries 16 Channel T1 Over Ethernet Multiplexer System Guía de usuario Pagina 59
- Pagina / 122
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
The [F1] Circuit Identifier lets you assign a name to the circuit if desired.
The [F3] Service Mode setting has two service modes which can select OOS (Out of Service) or IS (In
Service).
The [F3] Clock Source setting permits the use of an External clock source, or the Internal clock.
You can set the polarity of Tx or Rx clock to fit the requirement of different kind of DTEs.
Data Rate
PCM31: 64K~1984K PCM30: 64K~1920K Unframed: 2048K
To hav e st ab le V.35 c on fig ur at io n p er fo rm anc e, y ou mu st m ak e s ure t o s et t he co rre ct c loc k mo de .
Example clock mode settings:
Example 1
49
You ca n s et th e po la rity of Tx or R x cl oc k t o f it t he req uir em e n t o f di ffe r en t
kind of DTEs.
PCM31: 64K~1984K
PCM30: 64K~1920K
Unframed: 2048K
To have a stable V.35 configuration performance, you must make sure to
have set the correct clock mode. The following is the example of setting.
(1)
(2)
Date Rate
DTE DTE
SL-2100 SL-2100
Internal Recovery
DCE CLK DCE CLK
DTE DTE
SL-2100 SL-2100
EXT-DTE Recovery
INT DCE CLK
Internal Recovery
DCE CLKDCE CLK
DTE DTE
iMux iMux
Example 2
49
You ca n s et th e po la rity of Tx or R x cl oc k t o f it t he req uir em e n t o f di ffe r en t
kind of DTEs.
PCM31: 64K~1984K
PCM30: 64K~1920K
Unframed: 2048K
To have a stable V.35 configuration performance, you must make sure to
have set the correct clock mode. The following is the example of setting.
(1)
(2)
Date Rate
DTE DTE
SL-2100 SL-2100
Internal Recovery
DCE CLK DCE CLK
DTE DTE
SL-2100 SL-2100
EXT-DTE Recovery
INT DCE CLK
EXT-DTE Recovery
DCE CLKINT
DTE DTE
iMux iMux
System Configuration# RLH Industries, Inc. • 866-DO-FIBER • www.fiberopticlink.com! 59
- User Guide 1
- Contents 3
- Contents! 5 5
- Intended Audience 8
- Conventions 8
- General Safety Practices 8
- Caution - Severe Shock Hazard 8
- Laser Safety 8
- 2." Introduction 9
- Application Diagrams 10
- Front Panel 11
- LAN1 LAN2 LAN3 LAN4 MGMT 12
- Rear Panel 13
- 4 Channel E1 Module 13
- 4 Channel T1 Module 13
- 4 Channel RS-232 Module 14
- 4 Channel V.35 Module 14
- 4 PIN RJ-11 15
- PIN 8PIN 1 16
- E&M Application Diagram 18
- Acronyms 19
- 3." Before Installing 20
- Prepare for Installation 21
- Site Requirements 21
- Test Equipment 22
- 4." Quick Start 23
- Connect ethernet cables 24
- Connect data/phone equipment 24
- Start the system 24
- Management Interface 25
- Startup Loading Screen 26
- Self-diagnostic Screen 26
- Main Menu 28
- System Configuration 29
- Setting the device IP 31
- User Account Management 32
- SNMP Agent Configuration 33
- Setting the Trap IP 34
- Remote Server 34
- Local File 35
- Upgrade Status 36
- Upgrade Error Messages 37
- Software Reboot Status 37
- Network Time Synchronization 39
- Scheduling Job Management 40
- Networking Service Management 41
- Ping Failure Screen 43
- Event Management 45
- System Profile Management 48
- Configuration File Management 50
- Config Upload/Download Screen 53
- E1 Interface Configuration 56
- Example clock mode settings: 59
- T1 Interface Configuration 61
- 63
- PM Threshold Configuration 79
- Fault Parameter Configuration 83
- Alarm Severity Config 84
- External Clock Configuration 86
- External Clock Monitoring 87
- OE Protection Switching 88
- << Flow Chart>> 89
- Equipment Status Monitoring 90
- Lo is meaning Local site 91
- Performance Monitoring 93
- Path Alarm/State Monitoring 96
- Loopback/V.54 Testing 97
- Loopback Testing 98
- Notice function key [F8] 99
- PRBS Test 100
- One way PRBS test step: 101
- Event Browsing 103
- Front LCD controls 104
- LCD Menu Tree 105
- 106! Front Panel Controls 106
- Front Panel Controls ! 107 107
- 108! Front Panel Controls 108
- Using the web interface 109
- Local+Remote 110
- Only local side displayed 110
- Saving or loading profiles 111
- SNMP management 112
- 9." Appendix 113
- 10."Troubleshooting 114
- Power supply issues 115
- Verifying fiber cable 115
- Module installation 115
- Troubleshooting Guide 116
- Troubleshooting! 117 117
- 11."Specifications 118
- Service Module Specifications 119
- 12."Ordering Information 120
- Optical Modules 121
- 13."Support 122
Relacionado con productos y manuales para Redes RLH Industries 16 Channel T1 Over Ethernet Multiplexer System
(40 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales